VX Protector — ProTee VX Impact Shield
Why The VX Protector
Steel And Polycarbonate Armor For An Overhead ProTee VX
An overhead launch monitor lives directly in the flight path of every mishit. A thinned shank, a topped 3-wood off a mat, or a ricochet off the ceiling baffle can reach the ProTee VX faster than any reaction time. The VX Protector puts a thick steel frame and a toughened clear polycarbonate screen between the unit and the ball, without touching how the unit reads a shot.
It is purpose-built for the ProTee VX housing rather than adapted from a generic shield. The frame hooks on for a permanent, secure install, leaves the rear sockets and power button reachable, keeps airflow moving around the unit, and lets the golfer decide whether the infrared lights stay covered or exposed based on room lighting.
Built To Take A Hit
Thick Steel Frame, Toughened Clear Screen
Rigid Frame, Transparent Face
The load-bearing structure is thick steel finished in powder coat, so it resists scuffing, chipping, and the corrosion that shows up fast in a garage or basement build. The face is toughened clear polycarbonate — a shatter-resistant material that absorbs ball strikes instead of cracking apart, and stays optically clear so the unit and its indicator lights remain visible.
Nothing in the assembly sits between the sensor path and the ball in a way that changes data capture. Ball speed, club data, and spin readings are unaffected by the shield.
Airflow Preserved
The frame is open around the housing so heat from the ProTee VX vents normally during long sessions. No trapped-air enclosure, no thermal throttling risk.
Hook-On Install
The protector hooks onto the ProTee VX for a fast install that ends up permanent and secure.
Rear Access Kept
Sockets and the rear button stay reachable, so cables and power cycling do not require removing the shield.
Drop-Mount Ready
Can be fixed to a ceiling drop mount to offset the launch monitor down from a high ceiling.
Optional Camera Shields
Adjustable shields with camera cutouts add coverage over the lenses and infrared lights when wanted.
Launch Monitor Sold Separately
The VX Protector is an accessory only. The ProTee VX launch monitor is not included — see the ProTee VX Overhead Golf Launch Monitor product page for the unit itself.
Mounting And Setup Guidance
Overhead height, hitting-zone position, and drop-mount questions are covered on the ProTee VX Setup and Support page.
Key Features At A Glance
What The VX Protector Does
Direct Strike Defense
Shields the overhead ProTee VX from stray swings, topped shots, and errant ball strikes off the mat or screen.
Thick Steel Structure
The frame is heavy-gauge steel rather than plastic or aluminum trim, so it holds shape under repeated impact.
Toughened Polycarbonate
The clear face panel is impact-rated polycarbonate — it flexes and absorbs rather than shattering.
Powder Coat Finish
A durable powder coat resists scratching and corrosion in garages, basements, and unconditioned rooms.
No Reading Interference
Designed so the shield does not interfere with launch monitor readings or data capture.
Adjustable Camera Shields
Shield positions adjust to line up precisely with the VX cameras, with cutouts that eliminate glare.
Ball-Proof Cutouts
The camera hole cutouts are small enough that a golf ball cannot pass through them.
Infrared Choice
Cover the infrared lights for maximum protection, or leave them open when the lighting environment calls for it.
Specs And Compatibility
Dimensions, Materials, And Fitment
Where It Fits
- Overhead ProTee VX installs in a residential simulator bay
- Commercial swing studios and fitting rooms with public traffic
- Ceiling drop-mount installations in tall rooms
- Enclosure builds where the unit sits close to the hitting zone
- Rental, club, and academy bays with unknown swing quality
What Stays Accessible
- Rear sockets for power and data cabling
- Rear button for power and reset
- Camera lenses, via glare-free shield cutouts
- Infrared emitters, coverable or exposed by choice
- Ventilation paths around the housing
Camera Shields
Coverage That Adjusts To The Install
The lens and infrared area is the part of an overhead unit most builders worry about. The VX Protector treats it as a decision rather than a fixed design, so coverage matches the room instead of forcing a compromise.
Cover The Lenses Or Leave Them Open
Camera shields mount over the lens area with cutouts sized so a golf ball cannot pass through, while still leaving a clear optical path with no glare. Positions adjust so the cutouts line up exactly with the VX cameras on a given install.
- Adjustable AlignmentSlide the shields until the cutouts line up perfectly with the camera lenses.
- No GlareCutouts are open at the lens, so there is no reflective surface in front of the camera.
- Ball Cannot PassCutouts are small enough to stop a golf ball from reaching the lens.
- Infrared OptionalLeave the infrared lights uncovered when the room lighting requires it.
Who It Is Built For
The Installs That Need A Shield
Home Simulator Owners
Protects a significant launch monitor investment in a room where family and guests will also be swinging.
Swing Studios
Commercial bays see hundreds of swings a week from golfers at every skill level, including first-timers.
Tight-Room Builds
When ceiling height or room depth puts the overhead unit near the ball flight, coverage stops being optional.
Junior And Group Play
Wild misses and stray full swings are normal with juniors, leagues, and party-style group sessions.
What Is In The Box
Everything Needed To Install The Shield
The protector ships flat-packed in a single carton at 13.2 lb, with the frame, clear screen, and hardware needed to hook it onto the launch monitor.
- Steel Protector Frame
- Clear Polycarbonate Screen
- Adjustable Camera Shields
- Mounting Hardware
- Hook-On Brackets
- Installation Instructions
Mounting height, hitting-zone placement, and drop-mount setup are documented on the ProTee VX Launch Monitor Setup and Support page, along with software activation and calibration steps for the unit itself.
Pair It With The ProTee VX
Build The Bay Around It
The VX Protector is an accessory for a unit that is usually bought as part of a full simulator build. Both paths below include the ProTee VX launch monitor.
Pre-Built ProTee VX Packages
Complete Premium 4K SimKits pairing the ProTee VX with a BenQ AK700ST or Optoma short-throw laser projector, an enclosure choice or Carl's Place DIY enclosure, hitting mat, mount, and cabling.
Build Your Own SimKit
Pick the launch monitor, projector, enclosure, and mat individually and price the build as it comes together, then add the VX Protector as protection for the finished bay.
Buying the launch monitor on its own instead? The bare unit lives on the ProTee VX Overhead Golf Launch Monitor page.
Resources
Setup, Product, And Partner Links
ProTee VX Launch Monitor
Full product page for the overhead unit this protector is built for — specs, data points, and licensing.
View the product →ProTee VX Setup And Support
Mounting, calibration, software activation, and troubleshooting for the ProTee VX install.
Open the support page →Reseller And Installer Program
Dealer and installer pricing for shops building ProTee VX bays for clients.
Apply to the program →Questions
VX Protector FAQ
Is the ProTee VX launch monitor included?
No. The VX Protector is an accessory only. The launch monitor is sold separately on the ProTee VX Overhead Golf Launch Monitor product page.
Will the protector interfere with launch monitor readings?
No. The VX Protector is designed so the frame and clear polycarbonate screen do not interfere with how the ProTee VX captures club and ball data.
What is the VX Protector made of?
A thick steel frame with a powder coat finish, paired with a toughened clear polycarbonate screen. Steel handles the structural load and the polycarbonate absorbs ball impact without shattering.
Do the camera shields have to be installed?
No. The camera shields are optional. Install them for maximum coverage over the lenses and infrared lights, or leave the infrared lights uncovered if the room lighting environment works better that way.
Will the camera shields cause glare in the camera view?
No. The shields have cutouts at each camera position so there is no material in front of the lens and no chance of glare. The cutouts are small enough that a golf ball cannot pass through.
How does the protector install?
It uses an easy hook-on installation that results in a permanent, secure fit on the ProTee VX. Mounting guidance is on the ProTee VX Setup and Support page.
Can it be used with a ceiling drop mount?
Yes. The protector can be fixed to a ceiling drop mount, which is the normal approach for offsetting an overhead launch monitor down from a high ceiling.
Are the rear sockets and power button still reachable?
Yes. The design keeps the rear sockets and button easily accessible, so cabling and power cycling do not require removing the shield.
Does it trap heat around the launch monitor?
No. The protector allows airflow around the launch monitor so the unit vents normally through long sessions.
What are the dimensions and shipping weight?
The product measures 33.5″ × 8.2″ × 8.3″ (85 × 20.9 × 21 cm). It ships in a carton measuring 35.4″ × 8.5″ × 2″ (90 × 21.5 × 5 cm) at a boxed weight of 13.2 lb (6 kg).
Does it fit any other launch monitor?
No. The VX Protector is built specifically around the ProTee VX housing. It is not a universal overhead shield and should not be fitted to other launch monitors.
Is it suitable for a commercial swing studio?
Yes. The steel frame and permanent hook-on install are intended for both home golf simulators and professional swing studios where the bay sees heavy daily traffic.
Can it be added to a ProTee VX simulator package order?
Yes. It can be added to any order alongside a bare launch monitor, a pre-built kit from the ProTee VX Golf Simulator Packages collection, or a custom build from the SimKit builder.
What support comes with it?
Elite Sim Golf handles fitment questions, install guidance, and any shipping damage claims directly. Support requests can start from the ProTee VX Setup and Support page.
The Elite Sim Golf Advantage
Bought From A Simulator Builder, Not A Marketplace Listing
Accessories like this get bought once and used for years, so fitment accuracy and post-sale support matter more than a listing price. Elite Sim Golf sells the ProTee VX, its packages, and its accessories as one system.
Fitment Verified
Sold alongside the ProTee VX itself, so compatibility questions get answered by people who install the unit.
Fast Fulfillment
Orders are processed quickly and shipped in the manufacturer carton with damage protection.
Full-System Sourcing
Launch monitors, projectors, enclosures, mats, mounts, and accessories all come from one supplier.
Real Support
Install help, mounting guidance, and troubleshooting handled directly rather than routed to a manufacturer queue.
Bottom Line
A single mishit into an unprotected overhead launch monitor costs far more than a shield. The VX Protector is the purpose-built way to keep a ProTee VX out of the ball flight permanently, without giving up data accuracy, airflow, or rear access.